Warming of gate of garage allows to embroider possibilities of application of this room considerably. After carrying out similar works it is possible to use it not only for storage of the personal vehicle, tools and garden stock, but also vegetables, and the curlings prepared for the winter. All works on warming of garage can be conducted qualitatively independently.
Gate in garage are the main source of heatloss. High-quality warming of this area allows to make use of the room by more comfortable in cold season. There are several ways of warming of gate in garage with use of modern construction materials. The correct mounting of insulating pie on gate allows not only to maintain the necessary temperature in this room, but also to avoid increase in humidity.
Materials and tools for warming of doors of garage
If independent performance of work on warming of oar door of garage is planned, it is necessary to use materials which it just will be to cut and record on surface of cloths. It is the best of all to stop the choice on:
- to mineral wool;
- expanded polystyrene;
- polyfoam;
These construction materials are produced in the form of plates or rolls, ready to installation, perfectly cut and can be attached to surface in different ways. It considerably simplifies mounting process. Carrying out warming of surface of oar gate of garage will require number of accessory materials, including:
- waterproofing film;
- construction glue;
- wooden bars with the section of 5Х5 cm;
- silicone sealant;
- moisture resistant plywood;
- aluminum adhesive tape.
In addition, it is necessary to buy set of tools, potrebuyushchikhsya in the course of performance of work in advance, including:
- abrasive paper;
- drill;
- knife;
- construction level;
- metal brush.
If iron gate are strongly struck with rust, their processing by special structure for its elimination can be required. In the course of works on warming of gate and the sites of walls adjoining to them also some consumables, including rollers, tanks for solutions, etc. can demand.
Surface preparation of gate of garage to warming
Isolation will not perform the function if previously not to carry out complex surface preparation of metal wings of gate. If garage old, it is necessary to examine attentively shutters for identification of the through slots which have resulted from corrosion. These places will need to be boiled thoroughly. Sealing of the available welding seams is obligatory.
The flaking coat of paint needs to be cleaned off. If the corrosion centers small, them it is possible to smooth out metal brush and then to process abrasive paper. In certain cases, when the most part of surface of gate of garage is covered with rust, for its elimination it is reasonable to use the Bulgarian with special disk. It will allow to carry out preparatory work quicker. After that it is necessary to apply on surface special anticorrosive primer for metal. It can be put with both normal brush, and airbrush.
It is necessary to consider that because of temperature drops between iron cloth and heater condensate can accumulate. It will create conditions for emergence of the centers of corrosion. To reduce risk of damage of metal before installation of heater the painting of surface is carried out. It will protect metal from corrosion further. After drying of this material it is possible to start forming of furring.
Production of furring for fastening of heater of gate of garage
Most often when warming garage gate mineral wool is applied. Warming with use of mineral wool will cost not much. This material it is possible to fix also without furring, but it is the best of all to make this design as it will simplify further fastening of facing material. For forming of furring it is necessary to cut neobkhodimy amount of bars with the section of 5х5 cm.
It is necessary to fix this design to power frame of cloths of gate. The trick of openings, necessary for installation of furring, requires drill. Before installation of elements of this design it is necessary to process them not less than 2 times antiseptic structure from all directions to reduce risk of rotting of wood and forming of fungal colonies under heater layer.
To power elements of gate the fastening of bars of furring is made by means of screws. In case at gate there is ventilation pipe, it is necessary to fix it on contour furring. Besides, it is necessary to examine walls to which gate fasten and if necessary to plaster them.
Warming of gate mineral wool
At the created furring the device of heat-insulating pie on inside of gate is possible. At first it is necessary to attach waterproofing membrane or polyvinylchloride film. These materials it is necessary to fix so that they accurately bent around furring walls. Any joints should be glued with aluminum adhesive tape carefully.
After that in cells of the created furring is established the minvat. It is very important that heater mats densely adjoined to surface. It is necessary to fill with heater all sites between furring elements. Thanks to soft texture of the minvat perfectly bends that facilitates mounting process. Over time there is caking of this material therefore it is necessary to take care that mats in furring densely adjoined to each other. Joints between plates of glass wool need to be glued with aluminum adhesive tape.
It is in certain cases reasonable to strengthen design of heat-insulating pie wood furring. This thermal insulation is extremely subject to moisture influence therefore outside of it it is necessary to close completely waterproofing film. When mounting this layer of pie it is possible to use the stapler. It is possible to fix film directly to wood furring. After that the top facing layer as which gypsum cardboard or moisture resistant plywood can act is installed.
Mounting of polyfoam when warming gate of garage
The hands it is simple to trim garage gate with such heater as expanded polystyrene. It is on sale in the form of plates. The democratic price, low heat conductivity and resistance to moisture influence belong to advantages of such material. For the best result it is possible to carry out warming at the same time by expanded polystyrene and isobosom. At this option of forming of heat-insulating pie the furring is optional.
Finishing of oar doors begins with fastening to surface of waterproofing film. After that expanded polystyrene is installed. This material is well cut therefore if necessary plates can give the necessary form. For filling of the remained gaps polyurethane foam is used. It is very important that there was no open space left which are not filled with thermal insulation material.
After carrying out installation of extruded polystyrene foam the mounting of isobosom is carried out. It is rolled insulating material. It needs to be established so that the aluminum covering has been directed in the room. Fastening can be carried out by means of the construction stapler, glue or screws.
Places of joints of the established mats need to be glued with aluminum adhesive tape. The ready surface will look beautifully and accurately, but nevertheless it is desirable to cover it with lining, gypsum cardboard or other finishing material which will be able to protect heat-insulating pie from mechanical damage.
Outer surface of door of garage
In regions where in winter time temperature can fall very low, also external warming is reasonable. It is necessary to move external warming before mounting internal. For performance of work it is necessary to use plates of expanded polystyrene or polyfoam as they are less subject to moisture influence.
It is desirable to make furring on outer side of doors. It will be for this purpose necessary to make through holes in the doorway for fastening of wooden elements. It will be necessary to pressurize these openings after end of external finishing work from the inside of gate.
After installation of furring the installation of waterproofing film is made. In spite of the fact that expanded polystyrene cannot napityvatsya by moisture nevertheless the congestion of water vapors in heat-insulating pie is undesirable. When cutting insulating material it is necessary to watch that the shear line was ideally equal. The cut plates have to enter densely between the bars forming furring.
For splice closure and slots it is possible to use polyurethane foam or water glass cement. After drying of data material it is necessary to cut off knife the acted surplus. Over insulating layer the waterproofing film fastens. After forming of heat-insulating pie it is possible to start facing of surface of gate of garage.
Installation of sealants on garage wings of gate
For decrease in heatloss it is recommended to establish rubber sealants on garage door. They provide dense adherence of shutters to each other and frame therefore any movement of air in this area is excluded. If at gate of garage there is gate of garage it is possible to use the sealant from rubber having circular section and diameter not less than 20 mm for its dense adherence to the field of gate.
This product has tail part therefore it can be attached easily on door of any type. It is necessary to fix heaters self-tapping screws with step of 15-20 cm. Tape tails surely should be missed the mark with construction adhesive in addition. For warming of bottom of gate of garage it is necessary to use special brush profiles which are specially intended for these purposes. It is necessary to have such sealant so that at full closing of brush were bent approximately at 1/3 lengths. For mounting of this product it is possible to use self-tapping screws.