Mounting of any climatic equipment – process difficult and labor-consuming, and therefore manufacturing companies and suppliers in the market recommend to use services of skilled masters. But during "high" season of working hands often is not enough, and therefore some handymen install conditioners.
Before ordering the conditioner to the house or office, surely specify whether your power supply network will cope with equipment power. The mistake on it, the very first stage, is fraught that it is necessary to go much on instances, to get the corresponding permissions, etc. It is simple to calculate power consumption – it is half or 1/3 from cooling power.
Mounting of the conditioner
It is the best of all to carry out mounting of conditioners before repair or during its carrying out, it will be possible to lay accurately electrical wiring, to strengthen brackets. In installation time of the equipment it is necessary to drill openings. Buying the conditioner, order services in mounting in the same company, the quality of works and speed of their carrying out in this case will be higher. Consumers make more than a half of complaint concerning mounting, but not concerning the equipment.
Mounting of the conditioner including independent, begins with installation of the automatic machine on electric guard and also with wiring updating. It is necessary to remember that old wiring can simply not cope with increased load – do not save on safety. All process of installation of the conditioner can independently be divided into several stages: - mounting of the internal and external block, - the device of openings and fastening of brackets, - pipe installation, - mounting of drainage, - work with electrical connections, - removal of air from system and trial start of the conditioner. As for the external block of the conditioner, it is the best of all to put it on not glazed balcony. It is necessary to provide free access to the block as periodically it is required to carry out scheduled or repair works Split system. The external block will be spaced from wall on 10-15 cm, otherwise in the summer, in hot weather, it will overheat. Fastenings have to be very reliable, brackets have to maintain the weight exceeding the mass of the block several times. Over the external block do small hood to prevent formation of icicles and skaplivany snow on the equipment. If the block is put on the first floor, then for protection against theft it is possible to place it in special cage, at distance to 2 m from the earth. Internal blocks do not put near heat sources, over bed or work table. So, near heating devices the conditioner will work simply incorrectly and will quickly fail, and over bed or workplace it will be unhealthy – the risk of catarrhal diseases increases. Air which goes out of the conditioner has to be distributed freely about the room – cabinets, walls or partitions can prevent in it, and then the necessary temperature will not be established. In the course of mounting the drilling of openings under interblock communications is by all means carried out. Openings drill at an angle to external wall down that it was possible to delete condensate easily. Pipe installation is considered the major stage, as a rule, it is stacked in box or hidden in wall.
Qualitatively executed mounting is lack of zalom, cleaning of pipes of shaving and competent rolling.
Security measures
Mounting of electrical connections should be trusted only professionals. Do not forget about safety, all works have to be carried out competently and accurately. Section of the used cable completely corresponds to conditioner power. Surely grounding is arranged, zaloma of drainage hoses and breaks are inadmissible. After the bunch of communications is laid in wall, the opening is filled with heat-insulating material to avoid drafts and emergence of moisture. After the main mounting works are performed, the master has to clean all conditioning system from air and moisture. If not to make it, there will be their interaction to freon that will negatively affect work of system of the conditioner, the term of its work will be reduced.
To find out whether it is correctly installed, start of system helps with the test mode, it is carried out to evaluate whether there is no vibration, whether holding additional actions (etching of coolant or recharge) is required.
If you ordered mounting in the same firm in which bought the conditioner, then and on the equipment, and for the carried-out works will provide you guarantee. Remember that she acts only if you observe all recommendations about operation of the equipment. Surely it is necessary to hold in due time preventive events, without allowing misuse of the equipment (for this purpose attentively read the instruction). At least, it is necessary to take care of timely cleaning of filters, it will prolong life cycle of the conditioner and will keep freshness of indoor air.