The far-sighted and qualitative optics is necessary for any car. It is possible to strengthen lighting own hands, having established biksenonovy a lens. For this purpose a few skills and simple tool kit are required.
Tools for installation of biksenonovy lenses
Let's consider how to make biksenonovy lenses in house conditions. Such lenses can be installed on any car and by that to reduce risk of accidents in night-time, and no difficult tools will be necessary for production.
To you I will the following tools are necessary for installation of new lenses in headlights:
- Head with a graggers on 10 mm
- Cross screw-driver
- Two minus screw-drivers.
Besides, office scissors, a marker, the hair dryer, nippers, the soldering iron, kruglogubets will be necessary.
Make sure that you have a weight the listed tool kit before starting installation of such important detail as a biksenonovy lens.
How to establish biksenon in the car
Before getting directly to work, it is necessary to understand a design of this lighting fixture briefly. The Biksenonovy lamp consists of the following basic elements:
- The module which contains a blind with the mechanism of the switch of a high and passing beam;
- Reflector
- Dimensional element of lighting
This optics is established in the regular reflector of the car. Advantage of a system is that it leaves an opportunity to adjust light both in manual, and in the automatic mode if such option is provided by a car design.
The optical system is connected to network in 12 Volts via the special module of ignition. When the main system of a design is clear, it is possible to start its installation. For this purpose it is necessary to take the following steps.
First of all, to remove a standard block headlight and to remove it on a plain surface, for example, a table. Then to remove all covers from a back wall of optics. To make it, rotate covers counterclockwise. When you finish, to you access to lamps will open. Pull the plug on yourself. On the majority of cars the plug of a passing beam is painted in green color, distant – in blue color
To pull out a lamp:
- Press a fixer of a passing beam down;
- Slightly remove aside.
- Lift a detail upward
- Pull out a lamp from the block.
The element of a distant luminescence is in the same way taken out. The cartridge of a dimension can be got from the place of landing without excess movements and difficult manipulations.
Take the cross screw-driver and remove a fixer together with a latch and caps. Do not forget to note the direction and the place of a clip on the case of optics by means of a marker. To pull out a detail, use the minus screw-driver.
Installation of a headlight
At first wipe with a dry and clean rag a headlight from dust. Especially carefully remove dust on contours where the most part of road dirt disappears.
Then divide the glass casing of a block headlight with a mask. Act carefully that these two elements stuck together with special chemical. At high temperatures it will become very liquid, at absolutely low – dense. Heat a headlight on a ring, respecting all rules of safety. It is possible to use also the ordinary battery. By means of the minus screw-driver divide two halves of a detail. It will be more convenient to begin with a narrow corner on which the blinker is located. Working, take also plastic latches.
Postpone that part of a headlight which turns on the case with a stuffing and the reflector, in one party, and in the second place glass with a mask.
Installation of a biksenonovy lens the hands in the car.
We start a final part of work. Pick up biksenonovy optics. First of all build in LED dimensions in a lens. It becomes a LED tape which length has to be equal to 100-110 santimer).
Smooth out wires and take the soldering iron in 40 Watts. Attach wires to a tape. When the place of soldering cools down, slightly process it a rag or a Q-tip which needs previously to be moistened in alcohol. Warm up a tape and paste in a lens.
Let's continue to mount a biksenonovy lens. The subsequent installation is made in a certain sequence. Adhere to the following chain, performing works: a mask – a lens - silicone laying – the reflector – H7 washer – a nut – a device fixture framework on screws – a latch.
The second detail is inserted into the reflector. Wires from a blind and dimensions are carried out through an opening of regular. Inside the washer invests, all design over is clamped by a nut.
Installation of biksenonovy lenses does not come to an end at this stage. It is necessary to mount a framework of fastening of a lamp which will keep on three screws. The xenon lamp is easily inserted and fixed on the place.
Connection of wires
The last and one of the most difficult stages – the correct connection of wires. It is necessary to treat them with extra care. To connect a biksenonovy lens. Connection of biksenonovy lenses to wires is made as follows. Four wires depart from a xenon set.
Two wires go to the ignition block to a lamp, other two – from a headlight for this block. There are two wires, red and black. Both are connected to the plug. The last on regular optics is put on a lamp of a passing beam. The black wire of the block is connected to black on a headlight (with a minus sign), red is connected to green (to the fact that has a plus).
The following step – installation of wires to a LED tape. This action is made with respect for the same polarity. The sign "plus" in this case is the blue wire, the sign "minus" - black.
It is necessary to connect lens blinds on a high and passing beam. We continue work, arriving similar to the first case. Black (a minus wire which leads to near lighting), it is connected to black, red (plus on a high beam) - to red.
To drill an opening in 28 millimeters in a cover of a window of a passing beam. Make it with the help by a special mill. It is possible to measure all parameters also by a caliper, having drawn a circle of the necessary size. The soldering iron make in it an opening.
Remove all excess hangnails with a stationery knife. Now work is almost finished and it is possible to start collecting a new headlight. It has to be already closed by a cover and is connected to wires. If you want to stick together two halves of optics, the hair dryer heat a part of a headlight and if necessary return the correct form of the case kruglogubets. Wait when substance becomes almost liquid and stick together optics halves on a contour upside-down.
In several places fix them by clip-on earrings. Now the headlight is completely collected and it is possible to start installation of blocks of ignition. Take self-tapping screws with a drill and fasten to a power machine design through a noise-insulating pro-rate and brackets.
That contacts of electronics were not destroyed, direct plugs strictly down. At this stage the installation of biksenonovy lenses in headlights can be considered as fully completed. It is necessary only to repeat all these actions with the second half of a block headlight.
Do not forget that all electric connections have to be carefully, qualitatively and are reliably isolated. If you neglect isolation, any insignificant hit of moisture on a wire will cause short circuit with high probability. The Biksenonovy headlight in this case will not work and it is necessary to correct breakage long. Following all rules, it is possible to establish xenon in headlights quickly by the hands.